How to Repaint Kitchen Cabinets

How to repaint already-painted kitchen cabinets: addressing yellowing and chip damage, changing color over dark paint, lighter prep than first-time painting, and a durable two-coat finish.

Decorate · Kitchen

Time: 1–2 weekends Cost: $100–$300 Difficulty: Intermediate By: HowTo: Home Edition

This guide is for cabinets that are already painted — you're refreshing a color, fixing a yellowing finish, addressing chip damage, or changing to a new color. Less prep than first-time painting, but with specific techniques for dealing with existing paint conditions that generic guides miss.

First-time treatment?

If your cabinets are raw wood, factory-finish, or stained-and-varnished (never been painted), see How to Paint Kitchen Cabinets — the full first-time process with deep prep and tannin-blocking primer.

Assess the Starting Condition First

The scope of this project depends on what you're dealing with. Three scenarios:

ConditionProcessPrimer needed?
Well-adhered paint, same or similar color, minor chips and yellowingScuff sand, fill chips, spot-prime bare areas, two coats of enamelSpot only
Well-adhered paint, significant color change (dark to light)Full scuff sand, full tinted primer coat, two coats of new enamelFull coat, tinted
Widespread peeling or delaminationStrip back — this is not a repaint. See first-time guideN/A — strip first

Why Cabinets Yellow — and How to Fix It Permanently

The cause is almost always oil-based alkyd paint oxidizing over time. The fix is repainting with a water-based alkyd hybrid enamel (Benjamin Moore Advance, SW Emerald Urethane Trim Enamel) — these resist yellowing. Over yellowed areas specifically: apply shellac-based Zinsser BIN primer before topcoat to block both grease stain and tannin bleed.

The Steps

01 · Number and photograph all doors, then remove

Same as first-time painting — number every door and its cabinet opening with tape before removing anything. Remove doors, drawer fronts, hardware.

02 · Fill chip damage

Surface chips: lightweight spackling, let dry fully, sand smooth with 150-grit then 220-grit. Deep chips or gouges into substrate: vinyl-modified wood filler. Feather edges flat. Spackling shrinks — let it dry fully before sanding; if it sinks below the surface, apply a second fill and re-sand.

03 · Degrease

Even with existing paint, grease must come off before new paint is applied. TSP substitute, wipe, dry. Extra attention to cooking zone cabinets.

04 · Scuff sand entire surface — 150-grit, then 220-grit

All surfaces should be dull and matte — no shiny areas. Use a sanding sponge on raised-panel profiles. Tack cloth thoroughly after sanding.

05 · Prime strategically

Same color refresh: spot-prime only at bare fills and scratches. Color change: full coat of tinted primer (match to new color). Yellowing: BIN shellac primer over all yellowed areas. Allow to dry, sand with 220-grit, tack cloth.

06 · First and second coats of cabinet enamel

Same painting sequence as first-time application: raised-panel doors use panel→profile→stiles→rails order. Long strokes, wet edge, do not overwork. Overnight between coats. 220-grit scuff between coats. Two coats standard; three if color change requires it.

07 · Cure, reinstall, keep touch-up paint

Handle after 24–48 hours. Do not close against frames for 5–7 days. Label and store a small jar of the finish paint for touch-ups over the next 2–3 years.

Invisible touch-ups only work within 2–3 years. After that, the original paint has color-shifted and sheen-shifted enough that spot touch-ups will read as patches. A full door repaint is the only invisible fix on older cabinets.

Related Guides

For the wider kitchen: kitchen cleaning guides for the degreasing step, the painting trade guides and the kitchen hub.